Skip to main content

Oil Transfer Pump Maintenance Tips

The following article mainly introduces the maintenance tips for oil transfer pump of diesel engine. If you are interested, take a few time to read it.

Oil pump is an important part of diesel generator. In the process of using the diesel genset, only regularly checking and maintaining the oil transfer pump can guarantee the normal operation of the generating set.

Maintenance tips

1. Before installing the oil transfer pump on diesel generating set, check whether the model and specification are correct or not; remove rust preventive oil and choose the appropriate thickness gasket. In order to avoid piston running improperly, the gasket should avoid too thin or thick, and the tightening torque should be uniform to prevent damage to the oil pump.
2. The coarse filter core within the oil pump is easily blocked by cotton and other dirt, you should reguarly check and clean it. If the strainer is damaged, you should repair or change it timely.
3. There is a rubber seal between the hand oil pump piston and the hand oil pump body. Do not remove the rubber. If the rubber ring is damaged, you should replace it timely.
4. Ensure the elasticity of “Four spring” for plunger oil transfer pump. “Four spring” is divided into piston spring, tappet (roller) spring, oil inlet valve spring and oil outlet valve spring. If the spring elasticity is weakened or broken, you should replace it timely or add pad to adjust to avoid causing damage to the diesel generator.
5. The hand oil pump of the generator set must be pressed back after using, at the same time, tightening the button to prevent oil leakage that is caused because the pressure is not tight between the hand oil pump and the rubber ring.
6. After using the oil transfer pump for a long time, checking the parts. If the phenomenon like the wear, sag, and pocking mark appear on the valve surface, it should be repaired timely or replaced. 
7. When the diesel generator set is in the state of parking for a long time, to prevent the piston and the pump body or the tappet and the tappet suit from being corroded by water, the rust preventive measures must be taken. When the generator set is power off, you should replace the lubricating oil (contains water, diesel oil and other impurities) in the sump of fuel injection pump.


标签：

Comments

Post a Comment

Popular posts from this blog

What Is the Difference Between Electric Motor and Electric Generator

An electric motor is an electrical machine that converts electrical energy into mechanical energy. Most electric motors operate through the interaction between the motor's magnetic field and winding currents to generate force. In certain applications, such as in regenerative braking with traction motors, electric motors can be used in reverse as generators to recover energy that might otherwise be lost as heat and friction. An electric generator operates in the reverse direction, converting mechanical energy into electrical energy. Electric generator can be divided into various type, open type, silent type, trailer type, portable type and container type, etc. Electric generator is mainly composed of diesel engine & alternator. Electric generator set is mainly composed of engine, alternator, control module, and common base. Electric generator :- Electric generator is a type of machine which converts mechanical input (energy) into electrical output (...
1 comment
Read more

Main Structural Features of Natural Gas Engine - Weichai WP13NG Gas Generator

1.1 Main structural features of natural gas engine ● A cover per cylinder, dependable operation, easy disassembly. ● Frame-type main bearing structure and high complete machine rigidity which benefits the reliability and  service life of complete machine. ● Electronic throttle is adopted to control engine revolving speed. ● Mixture supply system uses mixer to regulate air-fuel ratio and adopts proportional mix and supercharged inter-cooling method to stabilize gas supply. ● Water-cooling middle case turbocharger applicable to gas engine features is selected and circulating  water shall be used to cool down turbocharger lubrication cooling oil so as to effectively prevent  pressure bearing lubricating oil from coking and to improve turbocharger’s reliability. ● Designed gas mixing system satisfies gas fuel features to effectively support stable lean burn and enhance thermal efficiency. ● Two pairs of friction couples of inlet, outl...
Post a Comment
Read more

Factors to Consider When Choosing Diesel Generators for Data Centers

As the core facilities for data storage, processing and transmission, data centers’ stability and reliability are crucial in today's information age. Once the power supply interruption occurs, it can lead to data loss, business interruption, and even more serious consequences. Therefore, investing in one or more high-quality   diesel generators   for a data center is a key measure to ensure the continuity of power supply. Today, Dingbo Power will share several key factors that need to consider when purchasing data center diesel generator sets. Power requirements First of all, assess the power requirements of the data center based on the actual load conditions. This includes calculating the total power requirements of all critical equipment, as well as considering a possible increase in future needs. When selecting a diesel generator for the data center, make sure that the unit’s rated power can meet or exceed the peak load demand of the data center to ensure stable power suppl...
Post a Comment
Read more